Strainer Cleaning Assembly
Strainer Cleaning Assembly
NP-207-S-SA | Strainer Cleaning Assembly Specify Motor Type/Voltage |
|
NP-207-S-1 | Strainer Shaft | |
NP-207-S-2 | Brush Hub Bottom | |
NP-207-S-3 | Brush Hub Top | |
NP-207-S-4 | Brush Hub Washer | |
NP-207-S-5 | Strainer | |
NP-207-S-6 | Strainer Top | |
NP-207-S-7 | Strainer Bottom | |
NP-207-S-9 | Flue Brush | |
NP-207-S-10 | 5/8" x 1/2" Shoulder Bolt | |
NP-207-S-11 | 1/2-13 nylon Locknut | |
NP-207-S-12 | 1/2" x 1/2" Shoulder Bolt | |
NP-207-S-13 | 3/8-16 Nylon Locknut | |
NP-207-S-15 | Drive Pinion | |
NP-207-S-17 | Idler Pinion | |
NP-207-S-19 | Brush Gear | |
NP-207-S-21 | Strainer Gear | |
NP-207-S-30 | Snap Ring | |
NP-207-S-32 | Top Plate | |
NP-207-S-32-DI | Top Plate - Dual Idler | |
NP-207-S-34 | Bottom Plate | |
NP-207-S-50 | Stand Off | |
NP-207-S-54 | 10-32 x 5/8" Socket Head Cap Screw | |
NP-207-S-70 | 1/4-20 x 1-1/2" Socket Head Cap Screw | |
NP-207-S-71 | 1/4-20 x 1/2 Socket Head Cup Point Set Screw | |
NP-207-S-72 | Plastic Nylon Ball | |
NP-207-S-74 | Ball Retainer | |
NP-207-S-76 | Pipe Union | |
NP-207-S-77 | Pipe Union Seal | |
NP-207-S-78 | Pipe Nipple | |
NP-207-S-GC | Gear Cover (OPTIONAL) | |
NP-207-S-GC-SS | Gear Cover Set Screw | |
NP-207-S-78-RV-SA | STRAINER CLEANER - RELIEF VALVE Replaces NP-207-S-78 On a Cycle Select Drive Package Equipped Machine |
|
NP-207-S-78-RV-10 | Close Nipple 1 | |
NP-207-S-78-RV-20 | l X 1/2 X 1 Reducing Tee | |
NP-207-S-78-RV-30 | Pipe Nipple 1 X 3-1/2 | |
NP-207-S-78-RV-40 | Street Elbow 1/2 | |
NP-207-S-78-RV-50 | Close Nipple 1/2 | |
NP-207-S-78-RV-60 | Relief Valve | |
NP-207-S-92 | Hex Driver | |
NP-207-S-94 | 10-32 x 3/8" Hollow Cup Point Set Screw | |
NP-207-S-96 | Hex Drive Shaft for Bisson Motors | |
NP-207-S-98 | Hex Drive Shaft for Brother Motors | |
NP-207-S-100 | 1/4 - 20 x 1/2 Hollow Cup Point Set Screw | |
NP-207-S-125 | 115 Volt Gear Motor | |
NP-207-S-125-C | Capacitor - Replacement Part for NP-207-S-125 | |
NP-207-S-200 | Strainer Assembly (5, 6, 7 ,21) | |
NP-207-S-250 | Strainer Gear Top Assembly (6, 21) | |
NP-207-S-300 | Brush Hub Assembly (3, 19) | |
NP-207-S-400 | Instructions for NP-207-S-SA | |
NP-207-S-510 | 208/230/260 Volt Gear Motor | |
NP-207-S-520 | 340/460/575 Volt Gear Motor | |
NP-E4-10 | 18 Gage 4 Cable | |
NP-E12-5 | Butt Splice | |
NP-E13-17 | Female Disconnect | |
NP-E-11 | Plug 15A 125V | |
NP-M2-16 | 10-32 x 2" Socket Head Cap Screw | |
NP-M3-16 | 1/4-20 Socket Head Cap Screw | |
NP-M4-8 | 1/4-20 SAE Jam Nut - Unplated (UNC) |
- A unique design that provides a continuous gear driven brush cleaning motion for the cutting oil strainer assembly
- Prevents metal chips and fines from clogging strainer which can interrupt or stop the flow of cutting tool oil
- Reduces the chance of costly "tooling smoke shows"
- Maintenance free
- Easy installation and low cost
- Patented